Hello Raisa
It should not be difficuet to carete F4 input help in BWA.
Call transaction RSDDB, select 'F4 Input Help' then enter an object name or click F4 help to select an Object at 'Master Data Index' field.
Are there any error messages in the job log or BWA trace files like TREXNameserver or TREXIndexServer? (see KBA 2068016, 2053196).
Can you create the index that has red status using RSDDTREX_SINGLE_TABLE_INDEX report (see note 1789310) ?
Kind Regards,
Natsuka Rastert
Hi.
I would like to achieve a "Filter and Drill Down by [free characteristic from the query]" using the Design Studio crosstab component.
Ideally, this would happen on selection (tap) of the table row.
I'm on Design Studio 1.5.
Example: Initially, all divisions are displayed. I tap a division and the crosstab is drilled down to the materials in this division, which are being shown instead of the division in the first column.
I could also use a hierarchy. However, I want to exclusively jump to the next level, hiding the other values.
The crosstab itself doesn't need much more features than this drill-down, as this functionality is intended for a slim mobile app.
The "navigate back" function should be realizable through a separate button.
(How) is this possible? Can I access the selected values in the crosstab's "On Select" event? I dont see the "Data Selection"-functionality for the crosstab.
Maybe it needs to be done on data source level?
Any ideas appreciated – Thanks!
Best,
Moritz
Hi Adrian,
The "Requested server name not found" error indicates that it cannot find "SYBASEDB" (your -S parameter) in the sql.ini file. Please check in %SYBASE%/ini/sql.ini and add it.
Also, -H allows you to provide a hostname. Perhaps you want to connect to the server using the IP address. In that case, use this format:
isql -Usa -Ppassword -S<ip addr>:<port>
or
isql -Usa -Ppassword -Swrkredhat6.0x64:<port>
Regards,
Mark
Hi Holger,
Thanks for your inputs.
I tried adding the modules, but I am facing following issues -
For Inbound
---------------------
1) Adding in sender AS2 channel - message is failing at partners end, not reaching PO.
2) Adding parameter in EDISeparator channel - not working, A2A view I can see the message but cannot see in B2B view.
For Outbound
----------------------
Adding in Idoc Sender channel , cannot see in B2B view. It is visible in A2A view only.
Please guide over this.
Thanks,
Nidhi
David,
I am not sure you can do this in Metapedia. I think you can only send MP Approver Group or Users in that group.
Interesting requirement though. SAP would probably suggest to raise an idea:
regards
Adrian
Hello,
I have the same need to create FO in a z program. I followed the Dragos's explantions but did not understand how to create location.
Could you please help me.
Hi-
I am in the process of upgrading to SAP BW 7.4 and am noticing some discrepancies in our results, Bex is displaying the word "Error" concatenated in with the values. Does anyone have any ideas of what could be causing this? Please take a look at the attached screen shot. 
| SAP_BW | 740 | 0012 | SAPKW74012 | SAP Business Warehouse |
| ] |
Hi Guru
My customer has run for same period and year "flb1n and S_ALR_87012082 report" but for each report obtains different amount in local currency.
After that I have run the program TFC_COMPARE_VZ and appears the following message: No differences occurred
This information is not true because I have the differences.
The program TFC_COMPARE_VZ can't extract the difference because there is the following message: Secondary index differs. Account type: D.
So I can't run the program TFC_ADJUST_VZ.
Can you help me? Because appear the message: Secondary index differs. Account type: D.?
Thanks a lot
Rossella
Message was edited by: Rossella Fiorella
Hello all,
I want to cancel without manual intervention.
Some jobs we have setup runs through the night . If some issue happens it runs for hours.
so if there is a way kill it after lets say 1 hour that will be great.
Thanks,
Raneetha
Hi,
Can any one help to send the programme for creation of Equipment BOM BDC Programme.
jQuery.sap.require("sap.m.MessageToast");
Hi Denise,
if you are looking for a solution at webi side, take a look at
http://scn.sap.com/thread/3822947
REgards,
ROgerio
Why don't you just simply turn on the JDBC trace in SAP HANA Studio and see how it's done there?
Typically, if you have frm 2 installed and the legacy in the config, that is about it.
If you have CR 1-5 or CR 10.2 (these would be from VS 2005 and VC 2005 respectively) uninstall them.
Check your CR references, make sure they are v. 13.x
Tell me more about this:
since asp.net 5 doesn't read it by default, i forced the configuration builder to load it
asp .net 5?
- Ludek
Yeah, I have strings that look like these:
10
6
8
9&11
5&10
Right now I have this formula:
stringvar array myarray := Split({mystring}, "&")
myarray[1]
This gives me the first number. Now I need to access the second number when it is there? How should I do it?
I tried using another formula:
stringvar array myarray := split({mystring}, "&")
myarray[2]
However, for all the strings with only 1 number I get an error. This is why I wanted to do
stringvar array myarray := split({mystring}, "&")
if( isnull(myarray[2])) then myarray[1]
Déjala para que se actualice regularmente con el campo Total del documento
Hallo Manuel,
was mir hier adhoc einfällt, sofern ein neuer Mandant nicht in Frage kommt, ist ein B1i Flow der bei Artikeln die eine bestimmte Eigenschaft haben, den Bestand auf 0 hält. Wichtig dazu wäre als Bewertungsmethode der Standardpreis. Ansonsten ist die Erstellung einer solchen Automatisierung relativ überschaubar.
Grüße
Lo que pasa es que te está mostrando los valores que tienes definidos para dicho campo, tienes que consultar la tabla de definición de campos de usuario y hacer el join con la tabla de usuario que estás manejando por medio del Field ID
Por ejemplo, tu tabla se llama @personarecibo entonces tu select debería ser algo como
select descr from ufd1 where tableid='@personarecibo'
Eso te va a traer la descripción de tus campos, es decir
juan
antonio
fer
susana
Saludos!
Hi Sónia,
Did you have any luck trying to find a solution for modifying payload before it goes out?
Thanks
Hi Guillaume,
I know this post is a bit old, but have you been able to figure it out? I am facing the same issue, and just cannot find a solution for it. I am running SP10 Rev. 102, but apart from that, configuration and error messages are exactly the same (either using XSSRV and EXTSRV).
Any help would be much appreciated!
Marco
